INTERBOND 201 PDF
Consult International Marine’s Interbond brochure on NauticExpo. Page: 1/2. Consult International Marine’s Interbond – Temperate brochure on NauticExpo. Page: 1/4. A hard wearing, surface tolerant, two pack epoxy primer/finish offering corrosion protection in one coat. A temperate version of Interbond is also available for .
|Published (Last):||26 September 2013|
|PDF File Size:||12.38 Mb|
|ePub File Size:||10.21 Mb|
|Price:||Free* [*Free Regsitration Required]|
Yes please, I’d like to hear about offers and services. DO NOT thin more than allowed by local environmental legislation. Open the catalog to page 4. There is no detrimental effect on product performance. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. Optimum performance is achieved when Interbond is applied over blasted steel.
When using in cargo holds, consult the Interbond Cargo Subject to re-inspection thereafter. Interbond low temperature grade is not suitable for use in Ballast Holds. For good cosmetics Interbond low temperature should be overcoated with Intergard or Intersheen Consult your International Paint representative for the system best suited for the surfaces to be protected.
Interbond 201 – Low Temperature
Marine Coatings Marine chemicals Marine lubricants. Glossy epoxies and polyurethanes may require abrasion.
As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating. Study the Material safety data sheets for the hazards of the chemical, learn the instructions on handling, storage and the emergency measures in case of accident.
DO NOT thin more than allowed by local environmental legislation. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. Stripe coating of complex structures is recommended.
Unmixed material in closed containers should be maintained in protected storage in accordance with information given in the STORAGE Section of this data sheet.
Stated figures for pot life, drying times and overcoating intervals are for low temperature product. Overcoating information is given for guidance only and is subject to regional variation depending upon Interbond low temperature grade is not suitable for use in Ballast Holds.
Contact permission We’d love to send you exclusive offers and the latest info relating to health and safety and safety data sheets by email and other electronic means. Stripe coating of complex structures is recommended. intergond
Describes the effects when workers come into contact with the chemical and how to proceed in case of an accident. Abrasive blast clean to Sa2 ISO If oxidation has occurred between blasting and application of Interbondthe surface should be reblasted to the intwrbond visual standard. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays.
We’d love to send you exclusive offers and the latest info relating to health and safety and safety data sheets by email and other electronic means. MSDS includes information such as melting point, boiling point, and flash point of a hazardous material. Use International GTA only in exceptional circumstances.
Interbond – International Marine – PDF Catalogs | Documentation | Boating Brochures
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. It is advisable that a small trial be carried out before applying a full coat over certain generic types. Always mix a complete unit in the proportions supplied. VOC values are typical interbojd are provided for guidance purposes only. Marine Coatings Page 1 of 4 Issue Date: Imterbond spraying large areas, application of a brush coat is recommended over pitted or rough surfaces to ensure full penetration.
DO NOT thin more than allowed by local environmental legislation.
Consult your International Paint representative for the system best suited for the surfaces to be protected. Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures.
It interbod good working practice to periodically flush out spray equipment during the course of the working day. Interbond is suitable for overlap onto most aged coating systems.
Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments.
Optimum performance is achieved when Interbond is applied over iterbond steel.
For use in cargo holds, on hatch covers and external decks. In common with all epoxy based coatings Interbond will exhibit chalking 2011 the film on UV exposure. There is no detrimental effect on product performance.